一般說明 | 數模轉換器 |
DAC | ESS Sabre32參考ES9018K2M |
採樣率 | 光學,同軸:192kHz; USB:384kHz DSD64,DSD128,DSD256 |
數字輸入 | 同軸,光學,USB micro-B PC / Android, USB-A for iOS,藍牙 |
數字輸出 | 同軸,光學 |
輸出電壓 | 5Vrms±0.1 |
頻率響應 | 20Hz〜20KHz(±0.2dB) |
信噪比 | 115dB(A加權) |
電池 | 鋰離子型DC 3.7V 5000mAh |
播放時間 | 長達7小時 |
尺寸(mm) | 34mm x 136mm x 178mm |
輸入阻抗:36.5千歐
頻率響應:± 1 dB的0 – 20KHZ
信噪比:110分貝
總諧波失真:<0.12%時為150mW
輸出功率:250MW(小於1%失真)
輸出阻抗:5.6歐姆
功率: 20W,內部-穩壓電源
輸入:
1個USB連接(支持24位@ 96kHz的10ppm的低抖動時鐘)
1 x同軸RCA(支持高達24位@ 192KHz的)
1 ×金鍍金RCA(線路電平輸入)
Pre-Amplifier
THD(+ noise): <0.008% (10Hz to 20kHz) Signal to Noise Ratio: >109dB “A”- wtd
Frequency Response: 15Hz to 75kHz -3dB max.
Inputs
1x Line Level RCA / Phono
USB type ‘B’ connector for computer/PDA
General
Dimensions – WxHxD (mm): 220 x 100 x 300
Weight (unpacked / packed): 3.4 kg / 4.1 kg
SABRE32 Ultra DAC (ES9016S x 2)
USB輸入 (PCM):44.1kHz, 48kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz, 352.8kHz, 384kHz (16, 24, 32bit)
USB輸入 (DSD):2.8MHz, 5.6MHz
同軸 / 光纖 / AEC / EBU輸入:32kHz, 44.1kHz, 48kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz (16, 24bit)
非同步傳送 (Asynchronous Transfer) 減少Jitter
3種 數碼過濾模式 (SHARP / SLOW / SHORT)
Lock Range Adjust 功能可有效減低Jitter
音訊升頻 (最高至384kHz / 32-bit)
保護式變壓器 (Shield Power Transformer) 有獨立線圈,有效分隔電源、數碼及模擬部份
完全平衡 (Full Balanced) 線路設計可減低噪訊
分散式線路設計 (Discrete Circuit) 令音質處理質素提升
平衡耳機端子:XLR3 / XLR4 x 2
非平衡耳機端子:STD x 1
“Fine Adjust” 可作細微聲量調節
附有增益調校 (Gain Switch) 以切合不同阻抗的耳機
數碼隔離器 (Digital Isolator) 可減低因USB產生的雜訊
採用NEUTRIK平衡端子
XLR3 / RCA可作前級 (Pre-Amp) 功能
低重心設計配合堅固機箱增加穩定性
消耗功率:35W
尺寸 (闊 x 高 x 深):296 x 101 x 271 mm
重量 (kg):6.3kg
前置端子-耳機輸出:非平衡 (STD) x 1,平衡 (XLR3) x 1,平衡 (XLR4) x 1
後置端子-數碼輸入:USB (type B) x 1,同軸 x 2,光纖 x 2,AES/EBU (XLR3) x 1
模擬輸出:非平衡 (RCA) x 1,平衡 (XLR3) x 1 (附有輸出水平 Fix / Variable變換及相位變換)
1x pair Phono (stereo) (A1). Gain 3dB; 1.4Vrms in for 2Vrms out
1x 3.5mm analogue stereo (A2). Gain 12dB; 500mVrms in for 2Vrms out. Analogue inputs overload
capability >40dB
1x Asynchronous USB 2.0 interface, 44.1–192kHz ≤24-bit. Jitter <90ps p-p. Apodising filter and upsampling of 44.1/48kHz inputs to 88.2/96kHz; MQA decode and render
1x pair phono (stereo) preamp out. Maximum output 3.1Vrms @ 1kHz, THD <0.001% @ 1kHz up to 3V
rms. Crosstalk <–70dB @ 1kHz. Output can be disabled via power button
2x 1/4in A-type stereo phone jacks. Maximum output 3Vrms off load, THD <0.002%. Output impedance
<100mΩ. Power output 250mW up to 42Ω. Short-circuit protected
1x 3.5mm stereo phone jack. Max output 3Vrms off-load, THD <0.002%. Output impedance 2.2Ω
Dynamic range: 127dB ‘A’ weighted
Noise: 4 uV ‘A’ weighted (high gain), 1.7 uV ‘A’ weighted (low gain) with no measurable noise floor modulation
Distortion: 0.00008% @ 2.5 V 300Ω; 0.00016% @ 6 W 8Ω
Output power (unbalanced): (@1% THD) 288 mW RMS 300Ω; 7.3 W RMS 8Ω
Output power (balanced): (@1% THD) 1.15 W RMS 300Ω; 18W RMS 8Ω
Output impedance: 0.042Ω
Stereo separation: 9 V RMS 300Ω -138dB
Dimensions: 5.2cm (H) 23.5cm (W) 23.8cm (D)
Input | USB3.0 B Socket (USB2.0 compatible) |
Formats | DSD256/128/64, Octa/Quad/Double/Single-Speed DSD DXD(384/352.8kHz), PCM(384/352.8/192/176.4/96/88.2/48/44.1kHz) MQA |
DAC | Bit-Perfect DSD & DXD DAC by Burr Brown |
Line Section |
|
Output | Audio RCA (SE) — 2.1V fixed 1V / 3.3V max. (variable) 4.4mm Pentaconn (BAL) — 4.2V fixed 2V / 6.2V max. (variable) |
Zout | <= 200 Ohm (BAL) <= 100 Ohm (SE) |
SNR | < -116dB(A) @ 0dBFS (BAL/SE) |
DNR | > 116dB(A) @ -60dBFS (BAL/SE) |
THD+N | < 0.0015% @ 0dBFS (BAL/SE) |
Headphone Section |
|
Output Power (@1% THD) | 4.4mm Pentaconn (BAL) 330mW@32 Ohm; 6.6V@600 Ohm; 16 Ohm – 600 Ohm Headphone6.3mm S-BAL (SE) 230mW@32 Ohm; 3.3V@600 Ohm 16 Ohm – 600 Ohm HeadphoneNote: Using 5v power. If powered from USB, power output may vary. |
Output Impedance | < 1 Ω (BAL/SE) |
THD & N | < 0.005% (125mW @ 32R) |
SNR | > 113dBA (6.2V BAL/3.3V SE) |
Power consumption | < 1.5W via USB power OR 5v DC (power supply not included) |
Dimensions | 160(w) x 117(d) x 35(h) mm 6.3″ x 4.6″ x 1.4″ |
Weight (Gross) | 0.8 kg (1.8 lbs) |
Warranty period | 12 months |
Specification
System: Closed Customized Android, with build-in streaming apps
Display: Touch 4.7-inch HD
Power supply: Separated power for analog and digital section
Analog: Low noise Toroidal transformer
Digital: Switching power supply
Analog circuit:
AKM AK4493 DAC
OPA2211 as low pass filter*
2X TPA6120A2 for headphone output
2X Muse8920 for pre-amp output
3rd Generation FPGA
CPAF Filter technology
KDS Crystal oscillator
Panasonic Tantalum capacitors
Headphone Outputs: 6.35mm single ended, 4.4mm & 4pin XLR Balanced
Pre-amp outputs: RCA & XLR Outputs
Digital input: USB, Coaxial, optical, LAN and external driver USB slot
Digital output: Coaxial & Optical
Output power:
Single ended 6.35mm – 540mW @ 32Ohm
Balanced – 1620mW @ 32Ohm
Wireless connection:
Wifi 2.4 & 5G
Support DLNA and AIrplay
Two-way Bluetooth 4.2, with LDAC support
Audio support:
PCM 32/384
DSD256 native, DSD512 software
8x MQA
Input |
|
Output |
|
Color |
|
Channel |
|
Class |
|
Amplifier chip |
|
Power (W) |
|
Remote Control |
|