color: | black |
housing: | Desktop |
amplifier channels: | 2 |
headphone Out: | 1 (bal., XLR 4-pole) |
dimensions: | 290 x 80 x 248 mm (B x H x T) |
Technical details:
Output impedance < 0,1 ohm
Maximum output current 300 mA.
Maximum output voltage JAZZ 3.7 V
Maximum output voltage JAZZ-FF 15 V @ 200 Hz
Discrete volume control. Typical stepsize 1.4 dB, 31 steps.
Gain switch. Maximum gain factors +0 / +16 dB
Crossfeed filter switch:
1. Stereo / crossfeed OFF
2. Crossfeed ON
1 pair of analog inputs
Input impedance 18 kOhm
Gold-plated input jacks.
Silver plated headphone jack (Neutrik).
Silver plated heavy duty switches
10 Watts toroidal transformer.
110V and 220V mains power switchable.
Power uptake 5 Watts
Built-in groundloop breaker.
Double regulated voltage lines.
Low impedance electrolytic buffer capacitors (Nichicon). Total Buffer capacity 39.000 uF.
Bypass capacitors in the power supply.
Polystyrol and polypropylen capacitors in the signal path.
Metalfilm resistors in the signal path.
OPA209 opamps biased into class-A.
A total of 4 BURR-BROWN BUF634 buffer amplifiers at the left, the right, and the ground output channel.
Active balanced headphone ground.
Signal paths and signal path components at the bottom side of the PCB for maximal shielding.
Sturdy anodized aluminium enclosure
Weight: 1.0 kg
Size: 22.2 x 10.6 x 6.0 cm
Output power | Balance out 2,000mWx2/40Ω, 800mWx2/600 Unbalance out 1,000mWx2/40Ω, 240mWx2/600Ω |
THD+N | Balance out 0.004%, unbalance out 0.004%, 1kHz |
Input signal , impedance | 1Vrms, 47kΩ for CH1 and CH-2 |
Frequency response | 10Hz – 120kHz -1.5dB |
AC power | AC100V -120V (50/60Hz) 40W for Japan and USA model AC220V – 240V 40W for Europe and Asia countries model |
Size | W260mm X D250mm x H100mm |
Weight | 3.5kg |
Inputs | 4.4mm Pentacon BAL | 4.0V nominal @ 0dBFS, 24 kOhm Zin |
RCA L/R Socket SE | 2.0V nominal @ 0dBFS, 1 MegOhm Zin | |
3.5mm Jack SE | 1.0V nominal @ 0dBFS, 1 MegOhm Zin | |
Max Output | Balanced | >15.1V/385 mW (@ 600 Ohm) |
>11.0V/1890 mW (@ 64 Ohm) | ||
S-E | >7.6V/196 mW (@ 300 Ohm) | |
>7.2V/1600 mW (@ 32 Ohm) | ||
THD & N | Balanced | < 0.0007% (4V out, 600 Ohm, 1kHz) |
S-E | <0.006% (@ 100 mW/1.27V 16 Ohm) |
Line Inputs: | 2 channels balanced (XLR) 2 channels unbalanced (RCA) |
Headphone Outputs: |
2 |
Transmition Range: |
0 Hz – 150 kHz (-3 dB) |
Input
Sensitivity: |
+6 dBu |
Input Impedance: |
10 kOhm |
max. Output Level: |
600 Ohm – 600 mW – 18.9 V
300 Ohm – 1050 mW – 17.8 V 100 Ohm – 1760 mW – 13.2 V 32 Ohm – 1400 mW – 6.7 V |
Dynamic Range (SNR): | > 129 dBa |
THD+N (@ -1 dB): | < -102 dB |
Crosstalk: | < -110 dB |
Power Supply: | 230 V / 115 V AC |
Case: | Desktop |
Dimensions: | 168 x 47 x 125 mm (WxHxD) |
錄音時
WAVE/BWF: 取樣頻率: 96/88.2/48/44.1 kHz, 位元深度: 24/16 bits
MP3 (MPEG-1 Audio Layer 3): 取樣頻率: 48/44.1 kHz, 位元率: 320/160/128 kbps
WAVE + MP3: 取樣頻率: 48/44.1 kHz, 位元深度: 16 bits, 位元率: 128 kbps
內建立體聲麥克風: 全向性Omnidirectional (OMNI)麥克風, 指向性Directional (XY)麥克風
類比輸入1/L, 2/R (XLR/TRS Combo型): XLR型(phantom powered), 1/4吋TRS耳機型 (平衡式/非平衡式)
Plug-in供電麥克風輸入(立體聲迷你耳機型)
輸入 : RCA x 2
輸出 : 6.3mm x 1
輸入阻抗 : 50K *
頻率響應10-300k *
總諧波失真約.09%*
輸出阻抗32-2000歐姆*
尺寸(Amp部分)*正面,從左到右,5.75“*深度,從前到後,4.25”*高度,無管,2.00“*高度用管,4.00”
尺寸(電源)*正面,從左到右,8.00“*深度,從前到後,5.75”*高度,3.00“*重量約8磅。
頻率響應:5赫茲至200赫茲(-3分貝)
串音:-84 dB的(@ 1kHz時)
總諧波失真:0001%(@ 1kHz時,0 dBu的輸入電平與團結增益)
噪聲:-97 dBu的
動態範圍:129分貝(@ 600歐姆阻抗)
阻抗:20歐姆平衡
最大輸入電平:+24 dBu的
輸出輸入端
耳機輸出:6,35毫米立體聲的trs連接
引腳接線提示=左,右環=,豎井=接地
阻抗:10歐姆
功率
輸出性能:
1.7W(+32,2 dBm的)@ 1 kHz和600歐姆
只有360mW(+25,6 dBm的)@ 1 kHz和30歐姆
電源
電壓:230伏交流電,50Hz/120V交流,60赫茲
功耗:最大。 5,6瓦/
保險絲:200-240伏交流電:200 mA/100-120伏交流電:400馬
高x寬x深:95 × 210 ×315毫米
用高腳的高度:127毫米
深度與音量旋鈕:335毫米
重量:2.65千克
1x pair Phono (stereo) (A1). Gain 3dB; 1.4Vrms in for 2Vrms out
1x 3.5mm analogue stereo (A2). Gain 12dB; 500mVrms in for 2Vrms out. Analogue inputs overload
capability >40dB
1x Asynchronous USB 2.0 interface, 44.1–192kHz ≤24-bit. Jitter <90ps p-p. Apodising filter and upsampling of 44.1/48kHz inputs to 88.2/96kHz; MQA decode and render
1x pair phono (stereo) preamp out. Maximum output 3.1Vrms @ 1kHz, THD <0.001% @ 1kHz up to 3V
rms. Crosstalk <–70dB @ 1kHz. Output can be disabled via power button
2x 1/4in A-type stereo phone jacks. Maximum output 3Vrms off load, THD <0.002%. Output impedance
<100mΩ. Power output 250mW up to 42Ω. Short-circuit protected
1x 3.5mm stereo phone jack. Max output 3Vrms off-load, THD <0.002%. Output impedance 2.2Ω
SABRE32 Ultra DAC (ES9016S x 2)
USB輸入 (PCM):44.1kHz, 48kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz, 352.8kHz, 384kHz (16, 24, 32bit)
USB輸入 (DSD):2.8MHz, 5.6MHz
同軸 / 光纖 / AEC / EBU輸入:32kHz, 44.1kHz, 48kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz (16, 24bit)
非同步傳送 (Asynchronous Transfer) 減少Jitter
3種 數碼過濾模式 (SHARP / SLOW / SHORT)
Lock Range Adjust 功能可有效減低Jitter
音訊升頻 (最高至384kHz / 32-bit)
保護式變壓器 (Shield Power Transformer) 有獨立線圈,有效分隔電源、數碼及模擬部份
完全平衡 (Full Balanced) 線路設計可減低噪訊
分散式線路設計 (Discrete Circuit) 令音質處理質素提升
平衡耳機端子:XLR3 / XLR4 x 2
非平衡耳機端子:STD x 1
“Fine Adjust” 可作細微聲量調節
附有增益調校 (Gain Switch) 以切合不同阻抗的耳機
數碼隔離器 (Digital Isolator) 可減低因USB產生的雜訊
採用NEUTRIK平衡端子
XLR3 / RCA可作前級 (Pre-Amp) 功能
低重心設計配合堅固機箱增加穩定性
消耗功率:35W
尺寸 (闊 x 高 x 深):296 x 101 x 271 mm
重量 (kg):6.3kg
前置端子-耳機輸出:非平衡 (STD) x 1,平衡 (XLR3) x 1,平衡 (XLR4) x 1
後置端子-數碼輸入:USB (type B) x 1,同軸 x 2,光纖 x 2,AES/EBU (XLR3) x 1
模擬輸出:非平衡 (RCA) x 1,平衡 (XLR3) x 1 (附有輸出水平 Fix / Variable變換及相位變換)
耳機放大器類別:隨身耳放
頻響範圍:為20Hz-80kHz的
適配阻抗:32Ω
失真度:<0.005%(20Hz-20kHz)
輸入接口:3.5毫米接口×1
輸出接口:3.5毫米接口×1
配件:交直流適配器
Pre-Amplifier
THD(+ noise): <0.008% (10Hz to 20kHz) Signal to Noise Ratio: >109dB “A”- wtd
Frequency Response: 15Hz to 75kHz -3dB max.
Inputs
1x Line Level RCA / Phono
USB type ‘B’ connector for computer/PDA
General
Dimensions – WxHxD (mm): 220 x 100 x 300
Weight (unpacked / packed): 3.4 kg / 4.1 kg
RETRO – Stereo 50支持藍牙、aptX(藍牙無線傳輸的最佳模式)和NFC的智能設備都可以通過無線配對與Stereo50連接,aptX能提供接近CD般品質的藍牙無線音頻傳輸,輕輕鬆鬆就能享受美妙的音樂。
無論您選擇哪種方式聽音樂,從數碼流到CD/DVD,Stereo 50都能給您帶來一個全新的音樂享受。
Stereo 50 擁有超清晰度音頻(DSD512、PCM768 kHz、2 x DXD)通過USB、同軸和光纖輸入,連接後即可享受您的音樂。
Stereo 50的4xEL84X和2xECF82靈感更來自於經典的Telefunken、Marantz和Leak放大器。Stereo 50主要運用A類,其25W+25W有著最真實的聲音,這一切的表現都展現出完美的設計。
|
Input impedance: 36.5 KOhms
Frequency response: ± 1 dB 0 – 50Khz
Signal to noise ratio: >96dB
THD: <0.03% at 30ohm with 1W ouput
Channel separation: >73dB
Output power: 2W at 16 Ohms
Output impedance: 5 Ohm @ 1W
Power dissipation: >20W, internal, regulated power supply
Inputs
2 x gold plated RCA (line level input)
1 x headphone jacks 6.35mm
1 x Soloist SL Headphone amp
1 x Power cable
1 x RCA pair input cable
1 x User Manual (including 24 months warranty registration information)
Weight: app. 2.5 kg
Colour: silver anodized aluminium
Dimensions: 140 mm x 80 mm x 210 mm
規格和功能:
輸入阻抗:47 歐姆
頻率響應:5Hz至35KHz
信噪比:> 九十八分貝
總諧波失真:<0.001%, 至6mW/300歐姆
頻道分離:> 70dB/10kHz
輸出功率:650mW/300 歐姆,800mW/60歐姆
輸出阻抗:線路輸出60歐姆
功耗:<10W,內部穩壓電源
尺寸:180 毫米x 250毫米x 80毫米
連接器 (音頻):2 ×耳機插座6.35毫米
重量: 4.5 kg
顔色: 銀鋁陽極氧化
輸入阻抗:36.5千歐
頻率響應:± 1 dB的0 – 20KHZ
信噪比:110分貝
總諧波失真:<0.12%時為150mW
輸出功率:250MW(小於1%失真)
輸出阻抗:5.6歐姆
功率: 20W,內部-穩壓電源
輸入:
1個USB連接(支持24位@ 96kHz的10ppm的低抖動時鐘)
1 x同軸RCA(支持高達24位@ 192KHz的)
1 ×金鍍金RCA(線路電平輸入)