頻率響應:5赫茲至200赫茲(-3分貝)
串音:-84 dB的(@ 1kHz時)
總諧波失真:0001%(@ 1kHz時,0 dBu的輸入電平與團結增益)
噪聲:-97 dBu的
動態範圍:129分貝(@ 600歐姆阻抗)
阻抗:20歐姆平衡
最大輸入電平:+24 dBu的
輸出輸入端
耳機輸出:6,35毫米立體聲的trs連接
引腳接線提示=左,右環=,豎井=接地
阻抗:10歐姆
功率
輸出性能:
1.7W(+32,2 dBm的)@ 1 kHz和600歐姆
只有360mW(+25,6 dBm的)@ 1 kHz和30歐姆
電源
電壓:230伏交流電,50Hz/120V交流,60赫茲
功耗:最大。 5,6瓦/
保險絲:200-240伏交流電:200 mA/100-120伏交流電:400馬
高x寬x深:95 × 210 ×315毫米
用高腳的高度:127毫米
深度與音量旋鈕:335毫米
重量:2.65千克
Specification of the Power Amplifier Unit
T-Amp IC Tripath TA2024
Output Power 2x15W @4ohm
2x6W @8ohm(RMS)
Signal-to-Noise Ratio (SNR) 98dB
Dynamic Range 98dB
IHF IM Distortion 0.10% @ 1W, 4ohm
THD+Noise Audiophile Quality 0.03% @ 9W 4ohm
0.1% @ 11W 4ohm
0.1% @ 6W 8ohm
High Power 10% @ 15W 4ohm
10% @ 10W 4ohm
Power Efficiency 81% @ 15W 4ohm
90% @ 10W 8ohm
Input Audio IN RCA (Left/Right) x 1
Power Socket (5.5mm/2.1mm) x 1
Speaker OUT RJ45 x1
Other Volume & Knob Power ON/OFF switch x
Power Indicator (Blue LED) x1
Power Supply DC 12V-13.2V (max.)
4.2 Specification of the Headphone Amplifier Unit
Signal-to-Noise Ratio (SNR) 92dB
Power Output 3.0 Watts per channel on 33 Ohm
Headphone
Frequency response 15 Hz – 100 kHz -1db
Input Impedance 10k Ohms
Input Audio CD IN RCA (Left/Right) x 1 [3Vpp max.]
Specification of the Pre Amplifier Unit
Input Impedence 10K Ohms unbalanced
Max Input Level +18dBV
Frequency Response 25Hz – 150KHz (+/- 3dB)
Output Power 450 mW/side,THD+N:0.1% (@16 Ohms)
108 mW/side,THD+N:0.1% (@300 Ohms)
Maximum Gain 20 dB/channel
Input Audio CD IN RCA (Left/Right) x 1 [3Vpp max.]
Audio IN 3.5mm jack (Left/Right) x 1
Power Socket (5.5mm/2.1mm) x 1
Output Audio Headphone OUT 3.5mm jack x 1
Switch Knob Audio and power switch x 1
Power Supply DC 12V-13V (max.)
4.4 Specification of the AC Adaptor
AC Input Universal AC 100V-240V/50-60Hz
DC Output DC 12V 5A (60W)
DC Plug DC 2.1mm
Ripple & Noise <= 25mV
Over-load Protection 105%-150%
Over-voltage Protection 115%-150%
電源電壓:9V 電池,6V/9V/15V伏直流輸入
電流:50毫安/25毫安
最大放大: 0 / 14 dB
輸入阻抗:120 / 17 kOhm
輸出阻抗:<1歐姆
尺寸:8.9 x 6.6 x 2.2 cm
無電池重量:130克。
型式:晶管混合隨身耳擴
真空管:Raytheon 6418 x2
OP AMPS:JRC NJM2114DD(可更換)
頻率響應:10HZ~150kHz(-3dB)
建議耳機阻抗:16~32歐姆
端子:3.5mm輸入x1、3.5mm輸出x1
電源供應:AA(3號電池)x4,或鎳氫充電電池x4
尺寸:74.5×17.5x142mm(WxHxD)
重量:190公克
1x pair Phono (stereo) (A1). Gain 3dB; 1.4Vrms in for 2Vrms out
1x 3.5mm analogue stereo (A2). Gain 12dB; 500mVrms in for 2Vrms out. Analogue inputs overload
capability >40dB
1x Asynchronous USB 2.0 interface, 44.1–192kHz ≤24-bit. Jitter <90ps p-p. Apodising filter and upsampling of 44.1/48kHz inputs to 88.2/96kHz; MQA decode and render
1x pair phono (stereo) preamp out. Maximum output 3.1Vrms @ 1kHz, THD <0.001% @ 1kHz up to 3V
rms. Crosstalk <–70dB @ 1kHz. Output can be disabled via power button
2x 1/4in A-type stereo phone jacks. Maximum output 3Vrms off load, THD <0.002%. Output impedance
<100mΩ. Power output 250mW up to 42Ω. Short-circuit protected
1x 3.5mm stereo phone jack. Max output 3Vrms off-load, THD <0.002%. Output impedance 2.2Ω
耳機放大器類別:隨身耳放
頻響範圍:為20Hz-80kHz的
適配阻抗:32Ω
失真度:<0.005%(20Hz-20kHz)
輸入接口:3.5毫米接口×1
輸出接口:3.5毫米接口×1
配件:交直流適配器
型式:耳機擴大機
頻率響應:0Hz~20kHz
輸出功率:1.8瓦(每聲道)
最大輸出電壓:19V
訊噪比:大於120dB
總體諧波失真:小於0.005%
Pre-Amplifier
THD(+ noise): <0.008% (10Hz to 20kHz) Signal to Noise Ratio: >109dB “A”- wtd
Frequency Response: 15Hz to 75kHz -3dB max.
Inputs
1x Line Level RCA / Phono
USB type ‘B’ connector for computer/PDA
General
Dimensions – WxHxD (mm): 220 x 100 x 300
Weight (unpacked / packed): 3.4 kg / 4.1 kg
|
Cypher Labs便攜式耳機擴 驅動能力達600ohm
想出街聽歌都欣賞到媲美錄音室的音色,Cypher Lab新推出的便攜耳擴AlgoRhythm Picollo就是最佳選擇,外形輕巧迷你,只有140g重量,方便放進褲袋或手袋內。
近年高質耳機及線控耳機的普及大行其道,為了簡化生產程序各大廠家會使用 op amps來取代生產耗時的三極管,美國耳機擴音器專家Cypher Lab就不計較生產繁複,所以推出的AlgoRhythm Picollo耳擴,特別推出採用三極管作放大、獨立輸出及輸入的耳擴,輕易驅動高至600ohm阻抗的耳機。
AlgoRhythm Picollo特別用上三極管的設計,可增強耳機所需要的阻抗驅動能力達600ohm,配上不同的耳筒時可增加聆聽音樂的細緻度,使耳機傳遞出清晰通透的中高音人聲,同時提升低音的澎湃感。此外擁有獨立輸出及輸入規格,提供的輸出功率最高對應輸入5Hz-50kHz ±1dB,可優化輸出的音質,令單元驅動更流暢。
此外,內置一枚2,000mAH充電式鋰離子電池,使聆聽時間長達約最高30小時。充電使用Mini USB 5V,所以可以從電腦或USB充電器充電,靈活易用,不用擔心外出使用時突然沒電,聽得不夠盡興,隨時隨地將音樂推至最高境界。
Input impedance: 36.5 KOhms
Frequency response: ± 1 dB 0 – 50Khz
Signal to noise ratio: >96dB
THD: <0.03% at 30ohm with 1W ouput
Channel separation: >73dB
Output power: 2W at 16 Ohms
Output impedance: 5 Ohm @ 1W
Power dissipation: >20W, internal, regulated power supply
Inputs
2 x gold plated RCA (line level input)
1 x headphone jacks 6.35mm
1 x Soloist SL Headphone amp
1 x Power cable
1 x RCA pair input cable
1 x User Manual (including 24 months warranty registration information)
Weight: app. 2.5 kg
Colour: silver anodized aluminium
Dimensions: 140 mm x 80 mm x 210 mm
規格和功能:
輸入阻抗:47 歐姆
頻率響應:5Hz至35KHz
信噪比:> 九十八分貝
總諧波失真:<0.001%, 至6mW/300歐姆
頻道分離:> 70dB/10kHz
輸出功率:650mW/300 歐姆,800mW/60歐姆
輸出阻抗:線路輸出60歐姆
功耗:<10W,內部穩壓電源
尺寸:180 毫米x 250毫米x 80毫米
連接器 (音頻):2 ×耳機插座6.35毫米
重量: 4.5 kg
顔色: 銀鋁陽極氧化
A modern portable amplifier with a classic circuit design. The National+ is an Opamp-less design; using 10 matched pairs of triodes in a discrete component layout. This approach to amplification delivers a robust sonic presentation that compliments a wide variety of musical styles and tastes.
The National+ housing is CNC’d from a single block of aluminum, providing exceptional protection for ‘on the go’ applications. Sized at just 3.38”x1.8”x.75”, its diminutive footprint conceals a versatile performer. Capable of pairing with sensitive earphones when in ‘low gain’ it is also capable of driving planar magnetic headphones while in its ‘high gain’ setting.
The easy to use National+ features a 3.5mm single-ended input and output. This offers a simple solution to amplify your portable high resolution digital audio player or the sensitive low level signal from your favorite DAC. Its output provides 3 gain stages to provide the perfect match for an audiophile’s earphones and/or headphones.
Carrying case, USB cable for charging and ALO audio amp straps included with The National+.